Jaguar XK8 Manuel d'utilisateur Page 13
- Page / 123
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
12
DATE OF ISSUE: OCTOBER 1996
XK8 Range 1997User Instructions
NOTE: In the examples shown on this page, an ‘X’ is used where a number would appear on an actual Figure.
Reference Symbols
Reference symbols are used for three purposes:
• to allow the user to complete the individual system circuit to power supply or ground
• to refer the user to a related circuit
• to identify control module inputs, outputs and signal grounds
Battery Power Supply
This symbol represents a direct battery power supply and refers the user to Figure 01.1, 01.2 or 01.3.
Ignition Switched Power Supply
This symbol represents ignition switched power supply and refers the user to Figure 01.1, 01.4 or 01.5.
The suffix I indicates auxiliary power. Power is supplied in ignition switch key positions I (AUXILIARY) and II (IGNITION).
The suffix II indicates ignition power. Power is supplied in ignition switch key positions II (IGNITION) and III (ENGINE CRANK).
The suffix E indicates engine management switched power. Power is supplied in ignition switch key positions II (IGNITION)
and III (ENGINE CRANK) under ECM control.
Ignition Switched Ground
This symbol represents an ignition switched ground and refers the user to Figure 02.1.
This symbol without a suffix indicates CRANK. Ground is completed in ignition switch key position III (ENGINE CRANK).
The suffix I indicates auxiliary ground. Ground is completed in ignition switch key positions I (AUXILIARY) and II (IGNITION).
The suffix II indicates ignition ground. Ground is completed in ignition switch key positions II (IGNITION) and III
(ENGINE CRANK).
Figure Number Reference Flag
This symbol refers the reader to a figure number only. It does not refer to a flag with the same number on a different
figure.
As used in Figures 01.1 through 02.1, the reference flag refers the user to a continuation of the circuit. In this in-
stance, the user matches the number to a Power Supply or Ground symbol to trace the circuit.
In most other cases, it is not necessary to refer to another figure for completion of a circuit, as the reference flags are
used to indicate parallel circuits and circuits that share components. Most of the circuits where this situation occurs
are overlapped to avoid the necessity for cross-referencing to another figure. Exceptions to this rule are instances
where signals are transmitted to or received from other system circuits. When circuits are not overlapped, they are
noted by (CIRCUIT CONTINUED).
BPM Because the Body Processor Module appears numerous times, the abbreviation BPM is used in the reference
flags on Figures 01.2 and 02.1 in order to conserve space.
Control Module Input, Output, Data Link, Signal Ground and Network(s)
Input Output Serial and Encoded Signal Ground (SG) CAN (Network) SCP Network
Communications
These six symbols are employed to assist the user in visualizing the ‘logic’ of circuits containing control modules.
The symbols identify control module input, output, data link, signal ground and network pins. These symbols are also
employed on the corresponding data page.
X
X
II
X
E
X
I
X
XX
I
XX
II
BPMXX.X
DI O
SC
- 1997 Range Electrical Guide 1
- XK8 Range 1997 Introduction 2
- DATE OF ISSUE: OCTOBER 1996 3
- XK8 Range 1997Component Index 7
- User Instructions 10
- Figure and Data Page Layout 11
- Reference Symbols 13
- Harness Component Numbers 15
- XK8 Range 1997Connectors 17
- Harness Layout Harness Layout 19
- Fig. 01.1 25
- Fig. 01.2 26
- Fig. 01.3 27
- Fig. 01.4 28
- Fig. 01.5 29
- Fig. 02.1 30
- Fig. 03.1 31
- VARIANT: AJ26 NAS Vehicles 32
- VIN RANGE: All 32
- DATE OF ISSUE: OCTOBER 1996 32
- VARIANT: AJ26 ROW Vehicles 34
- Fig. 05.1 36
- Fig. 05.2 37
- Fig. 06.1 38
- Fig. 07.1 39
- Climate Control, Part 2 40
- VARIANT: All Vehicles 40
- Fig. 08.1 41
- Fig. 08.2 42
- Exterior Lighting – Front 43
- Fig. 09.2 44
- Fig. 09.3 45
- Fig. 10.1 46
- Fig. 10.2 47
- Fig. 11.1 48
- Fig. 11.2 49
- Mirror Movement 50
- Fig. 11.5 52
- Driver’s Seat – Memory 53
- VARIANT: Memory Seat Vehicles 53
- Fig. 12.2 54
- Fig. 12.3 55
- Fig. 12.4 56
- Central Door Locking 57
- Fig. 14.1 58
- Window Lifts Window Lifts 59
- Fig. 15.1 59
- Convertible Top 60
- VARIANT: Convertible Vehicles 60
- Fig. 16.1 61
- Fig. 16.2 62
- Fig. 16.3 63
- Fig. 16.4 64
- Airbag System Airbag System 65
- Fig. 17.1 65
- Ancillaries 66
- NOT USED 67
- The values 94
- PASSENGER 101
- POST CONNECTOR MOUNTING 101
- COmPOnentS 106
- XK8 Range 1997 111
- Appendix 111
Produits connexes et manuels pour Voitures Jaguar XK8
Voitures Jaguar XF Manuel d'utilisateur
(20 pages)
(20 pages)
Voitures Jaguar XJ Manuel d'utilisateur
(207 pages)
(207 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.730 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels